ATRIA Wi-Fi 5 Mesh System 1200 UK (3-pack)
All questions
ATRIA Wi-Fi 5 Mesh System 1200 UK (3-pack)
Wi-Fi and network troubleshooting
How can I add new Mesh units to the existing network I just configured? (CASE 2 : Atria Mesh App)
You can also add a Mesh node through the Atria Mesh App.
1Connect to the Wi-Fi of your mesh
To do so, connect to the Wi-Fi of the Mesh device that is connected to you router/modem.

2Download the App
Then download the atria mesh app

3Enter your credentials
Enter the username and password (admin/admin) to connect.

4Add Mesh Node
Click Add a New Mesh Node.

5Scan the QR code
Scan the QR Code located on the rear side of the mesh that you want to add.

Can I connect my mesh nodes via the Ethernet cable?
Yes, it is possible to connect your Mesh nodes via an Ethernet cable (RJ45). Any device can be connected
via RJ45 to any Mesh unit of your Mesh network.
The main Mesh must be connected to the internet box of your service provider via an RJ45
cable.
How can I have 2 different Wi-Fi Network with my Mesh?
You have different options to have several Wi-Fi Networks with your mesh units:
- You can set up your mesh unit as access points instead of mesh nodes.
- You can deactivate the band steering option of your device that creates a single Wi-Fi Network for the 2.4G or 5G bands.
- You can also configure a guest network.
We advise you to set up a guest network if you need to have several Wi-Fi networks at home.
How can I identify the IP addresses of the different Mesh units of my Network?
How can I identify the IP addresses of the different Mesh units of my Network? (Web UI)
1Connect to the Wi-Fi of the mesh
Connect to the Wi-Fi of the main mesh unit.

2Browse to the Web UI IP Address
Then, you must browse to the Web UI IP address

3Easy mesh Settings
Click on Easy Mesh in the left bar.

4Mesh Topology
Then, all the IP addresses of the Mesh units of your network are displayed in the Mesh Topology.

5Write down the IP Addresses
Write down the IP Addresses on a piece of paper. Then, type them in your browser to access the Web UI.

How can I identify the IP addresses of the different Mesh units of my Network? (App)
1Connect to the Wi-Fi of the mesh
Connect to the Wi-Fi of the main mesh unit.

2Access the App
Connect to the Atria Mesh app by entering the username and password.

3My Network
Click My Network.

4List of mesh devices
Click the Name of the Mesh Agent in the list.

5Write down the IP Addresses
Identify its IP Address and write it down.

6Other Mesh units
Repeat the same steps for any other mesh units.
How can I pair my mesh nodes if they are connected to my internet gateway via Ethernet cables?
1Plug the mesh
You must plug in the mesh unit to turn it on (there is no power button on the device) and connect it to your modem by using a RJ45 cable.

2Plug the second mesh unit
You must plug in the second mesh unit to turn it on and then connect it to the main mesh unit (LAN port) by using a RJ45 cable.

3Devices are configured
Wait a few minutes for both mesh units to detect the Internet configuration. Once the LEDs are green on both devices, they are configured.

4Remove the RJ45 cables from the secondary mesh units
You must remove the RJ45 cable from the second mesh unit and unplug it to install it in the room where you want to use it.
How do I configure my Wi-Fi mesh network (Case 2 : Ethernet Cable)
1Plugin the main mesh
You must plug in the mesh unit to turn it on (there is no power button on the device) and connect it to your modem by using a RJ45 cable.

2Plugin the second mesh
You must plug in the second mesh unit too turn it on and then connect it to the main mesh unit (LAN port) by using a RJ45 cable.

3Wait a few minutes during the configuration
Wait a few minutes for both mesh units to detect the Internet configuration. Once the LEDs are green on both devices, they are configured.

4Remove the RJ45 on the second mesh
You must remove the RJ45 cable from the seconds mesh unit and unplug it to install it in the room where you want to use it.
How do I use the Atria Mesh App?
1Download the app
Download the application for smartphone 'ATRIA MESH' on the App Store or the Google Play Store.

2Connect to the Wi-Fi of your Mesh
You must connect to the Wi-Fi of the Mesh with your smartphone.

3Log into the app
Then, login to the app with your credentials that should be 'admin' and 'admin' if you did not change it.

4Home Page
Now you are on the main page:
- Add a New Node: Where you can add a new Mesh unit to your Mesh Network.
- Attached Devices: Where you can check which devices are connected to your Mesh Network.
- My Network: Where you can check all the Mesh units connected to your Mesh Network.
- Wi-Fi Settings: Where you can edit and modify the SSID (Wi-Fi Network Name) and Password of your Wi-Fi Mesh Network.
- Guest Wi-Fi: Where you can set up and configure a 2.4GHz or a 5GHz Guest Wi-Fi.
- Wi-Fi Schedule: Where you can schedule a time period activation for your Wi-Fi Network.
- LED Control: Where you can turn ON or OFF the LEDs of your Mesh unit.
- LAN Settings: Where you can enable or disable a DHCP.
- Internet Settings: Where you can configure a DHCP Connection, a manual DNS, a PPPoE and set up a Static IP.
- System Settings: Where you can modify the Administration Username and Password to access the App.

How many Mesh units can I use in a Mesh network?
You can use up to 6 Mesh units simultaneously in your Mesh network.
The main one connected to your internet box and the 5 others paired via WPS to the main Mesh unit.
Warning: For a maximum coverage, put the mesh units in the rooms where the Wi-Fi signal is good, all the LEDS must be green.
How many Wi-Fi networks are provided with my Mesh unit?
Your Mesh network only has one main Wi-Fi network once the mesh agents and controller are paired together.
If you need to have additional Wi-Fi networks, you can configure Guest Wi-Fi networks.
For the mesh 1200, you can configure two guest networks, one for the 2.4G band and one for 5G band.
Please refer to the following procedure:
Can I configure a Guest Network for my Mesh network?
How should I name my Mesh units?
You can follow the procedure below to define the name of your mesh units in order to identify them easily.
1Download the app
Download the Atria Mesh App.

2Connect to the Wi-Fi of the mesh
Connect to the Wi-Fi of your mesh unit.

3Connect to the App
Enter the username and password before clicking Sign In.

4My Network
Click My Network

5Mesh Network Status
You will see the status of the coverage provided by your mesh units.
Please note that when the mesh units are displayes in grey, the coverage offered by the unit is not sufficient. In this case, you must change the position of your mesh unit.
If the mesh units are displayed in green it means that they are working properly and offering enough coverage.

6Main mesh unit
Click on the name of the mesh unit to access its information.

7Edit the name of the main mesh unit
Enter a new name and click Save.
The mesh controller should be named like this: Mesh1200-Main-
NameoftheroomThe mesh agents should be named like this: Mesh1200-Nameoftheroom

8Secondary mesh unit
For the other mesh units, click their name to access the information. Then, enter a new name and click Save.
How should I organize my Mesh Network to optimize my Wi-Fi network?
To optimize your coverage, you should install the mesh in the location where you have coverage issues in order to cover the widest area possible in your home. Please make sure that the mesh units are not located in a room where there is a load bearing wall, as the wall is thicker the Wi-Fi signal can have issues getting through it.
The following schema shows Wi-Fi coverage inside a house where mesh nodes are not located in the right area of the house to have a proper coverage.

The following schema shows Wi-Fi coverage inside a house where mesh nodes are located in the right area of the house to have a proper coverage.

1Download the app
Download the Atria Mesh App.

2Connect to the Wi-Fi of the mesh
Connect to the Wi-Fi of your mesh unit.

3Connect to the App
Enter the username and password before clicking Sign In.

4My Network
Click My Network

5Mesh Network Status
You will see the status of the coverage provided by your mesh units.
Please note that when the mesh units are displayes in grey, the coverage offered by the unit is not sufficient. In this case, you must change the position of your mesh unit.
If the mesh units are displayed in green it means that they are working properly and offering enough coverage.

I cannot access the internet after configuring my Mesh network,why?
I cannot access the internet after configuring my Mesh network, why?
There are several reasons why you cannot access internet after configuring your Mesh Network:
- The RJ45 cable is not properly connected to the internet box or the main Mesh or in the wrong port.
The internet connexion from the internet box is not working properly. - The main Mesh did not succeed to retrieve the network information of the internet box.
- The Mesh units are not paired together.
It takes too much time to have my Atria Mesh 1200 unit operational, is there something wrong?
After plug-in your first mesh unit and connecting it to the router, it usually takes up to two minutes for the router to identify the WAN/LAN IP address and connect to it. Once the mesh unit is ready
its LED will be green.
Then, plug-in the second mesh unit in a different room, the LED will be red. You must press the WPS of the first mesh unit for 5 seconds and then the WPS button of the second mesh unit for 5 seconds. Wait for approximately one minute for the devices to pair. Once the devices are paired the LEDs are green.
• If the pairing process does not work, please reset the two units to their factory settings by pressing the reset button of each unit.
Please refer to the following FAQ to see how to reset your mesh network: How do I reset my Mesh units to the factory settings?
• If the LED is still red on the first mesh unit, please check that the RJ45 cable is connected to the right Ethernet port: WAN port (mesh unit). If you put the cable in one of the LAN ports, the mesh unit will not be able to retrieve the information of the main internet network, so it will not be connected to the internet.
Please refer to the following FAQ to see how to configure your mesh network: How do I configure my Wi-Fi mesh network