Dual Band Repeater 750

No items found.

All questions

Dual Band Repeater 750

Credentials and Web UI access

LEDs, buttons and ports

Reset, reboot and firmware update

Settings and features

Wi-Fi and network troubleshooting

No items found.

Wi-Fi and network troubleshooting

How do I configure my repeater as a router?

TIPS: Before configuring your repeater, please check the following procedure to determine the location of your repeater: What is the best location for my repeater?

1Connect to the Web UI

Follow one of the procedures below to connect to the Web UI:

2Select the Router mode

On the mode switch located on the right side of your repeater, select the Router position.

3Router Wizard

Click Router Wizard.

4Router set up

Select the Static IP option to configure your network. Enter a name for each SSID and select the security type of your network, we recommend using the WPA2-PSK option. Click Apply to confirm.

TIPS: You will be able to connect to the Web UI by using the IP address of the repeater..

5Wait during the configuration

Please wait while the repeater is configuring.

Warning: Write down the passwords and the names of the Wi-Fi networks.

How do I configure my repeater as an access point?

TIPS: Before configuring your repeater, please check the following procedure to determine the location of your repeater: What is the best location for my repeater?

1Connect to the Web UI

Follow one of the procedures below to connect to the Web UI:

2Select the Access Point mode

On the mode switch located on the right side of your repeater, select the AP position.

3AP Wizard

Click AP Wizard.

4Access Point set up

Select the Static IP option to configure your network. Enter a name for each SSID and select the security type of your network, we recommend using the WPA2-PSK option. Click Apply to confirm.

TIPS: You will be able to connect to the Web UI by using the IP address of the repeater..

5Wait during the configuration

Please wait while the repeater is configuring.

Warning: Write down the passwords and the names of the Wi-Fi networks.

How do I configure my repeater?

Before configuring your repeater, please check the following procedure to determine the location of your repeater: What is the best location for my repeater?

1Connect to the Web UI

Follow one of the procedures below to connect to the Web UI:

2Select the repeater mode

On the mode switch located on the right side of your repeater, select the repeater position.

3Repater Wizard

Click Repeater Wizard.

4Network Scan

Your repeater will perform a scan of all the available 2.4G and 5G Wi-Fi Networks to determine the host network. Select the Wi-Fi Network Name of your router. Then, click Apply .

5Enter the information for the host and repeater networks

Enter the Wi-Fi password of your router and define the names for the Wi-Fi Networks of your repeater and click Apply.

TIP: You can check the Static IP box to set up the Static IP of your repeater.

6Wait during the configuration

Please wait while the repeater is configuring.

I cannot find my existing Wi-Fi network in the installation wizard of the repeater, why?

It is very likely that your repeater is too far from your modem/router. We recommend configuring your repeater in the same room as your modem/router and then changing its location to a different room.

WARNING: Please note that on your repeater if the network LED is lit in grey, red, purple or blinks in red the signal of the Wi-Fi host is too low.

I configured my repeater as an extender, but my broadband internet speed is not improved, why?

Repeaters can improve the Wi-Fi coverage, performance and connectivity locally but the broadband Internet speed is defined by your subscription of your Internet Service Provider.

What are the new Wi-Fi Networks information after the configuration?

Once the configuration is finished, you will see the following screen:

The name of the new Wi-Fi networks are written. Please write them down. the default passwords of the two Wi-Fi networks of the repeater are identical to the password of host Wi-Fi network you selected during the configuration.

What is the best location for my repeater?

Your repeater should not only be near to your modem/router, but also to a Wi-Fi dead zone. By doing so, your repeater will pick up the signal from the modem/router and repeat it to extend the coverage of your Wi-Fi Network.

Where can I find the Wi-Fi Network Information of my repeater?

You can find the information for the Wi-Fi Network on the product label, located under your repeater.

WARNING: Please note that the Network Name and Password of your repeater will change after the configuration. We strongly encourage you to write down the new information and tape it next to your repeater.

Which Wi-Fi frequencies (bands) does the repeater provide?

The repeater is dual-band which means that it uses the 2.4G and 5G bands. In other words, after the configuration, the repeater will create two Wi-Fi networks.