Credentials and Web UI access

How do I connect to the Web UI after setting up my device?

1Connect your repeater Wi-Fi Network

You need to connect to the repeater by RJ45 or to connect to one of the Wi-Fi networks that was created after the configuration.

.

2Browse to the Web UI URL

Type the URL in your browser.

3Login Page

Enter your admin password and click Login.

4Look for the IP Address

In the device information, look for the IP address of the repeater.

How do I connect to the Web UI of the repeater for the first time? (RJ45 Cable)

1Connect your repeater with a RJ45 cable

Connect your repeater to a computer via RJ45 cable.

2Browse to the Web UI URL

Type the URL in your browser.

3Login Page

Enter your admin password and click Login.

How do I connect to the Web UI of the repeater for the first time? (Wi-Fi)

1Look for the Wi-Fi Network information

Find the network information of your repeater on the product label, located under the repeater. Select the Network in the available network list and connect to it.

2Browse to the Web UI URL

Type the URL in your browser.

3Login Page

Enter your admin password and click Login.

How do I set up a new administration password?

1Connect your repeater Wi-Fi Network

You need to connect to the repeater by RJ45 or to connect to one of the Wi-Fi networks that was created after the configuration.

.

2Browse to the Web UI URL

Type the URL in your browser.

3Login Page

Enter your admin password and click Login.

4Password Settings

Click Password Settings.

5Create new password

Enter the following information before clicking Save & Apply:

• • New Password: Enter a new password..
  • Retype Password: Enter the same password as in the previous field.

Warning: Please note that we strongly advise you to write down your new administration password as you will need it to connect to the Web UI. If you forgot your password, please reset your device to its factory settings.

I cannot access the Web UI (http://strong.ap750) after setting up my repeater, why?

WARNING: It is normal that you cannot connect to the Web UI after the set up because the connection information are changed. Indeed, two Wi-Fi networks are created when the set up is completed. You must connect to one of this network to access the Web UI.

1Connect your router with a RJ45 cable

Connect your repeater to a computer via RJ45 cable.

2Browse to the Web UI URL

Type the URL in your browser.

3Login Page

Enter your admin password and click Login.

4Look for the IP Address of the router

In the device information look for the IP address of the repeater

TIP: The IP address of your repeater changes once it is configured to the Wi-Fi host.

I cannot access the Web UI with the URL (http://strong.ap750) during the configuration, why?

During the configuration of the repeater, you must connect directly to the IP Address of your repeater

WARNING: Once the configuration is completed a new IP address will be allocated to your repeater. You will not be able to access the web UI through this IP address.

What are the credentials to connect to the Web UI?

To connect to the Web UI, you only have to enter the administration password. The default administration password is admin.

.

Warning: Please note that we strongly advise you to change the administration password of your repeater to prevent hacking. To do so, please refer to How do I set up a new administration password?

What can I do in the Web UI?

The Web UI is divided into 5 sections, for more information see:

• Repeater Status: where you can see the list of connected devices (Devices), the information of the host network (Host Network), the 2.4G Wireless network (Wireless 2.4G) and the 5G Wireless network (Wireless 5G),
• Wi-Fi: where you can change the settings of the Wi-Fi Networks,, set up the WPS, etc.
• Repater Wizard: where you can configure the repeater.
• LAN Settings: where you can set a static IP, etc.
• Settings: where you can change the admin password, reset =/reboot the device, upgrade the software and change the time zone.

What is the IP address of my repeater?

Once the repeater is configured, you can find the IP Address of the repeater in the LAN settings.

Warning:This IP Address is allocated automatically and changes. If you want to have a Static IP for your LAN network, please refer to How do I set a static IP for my repeater?